![]() ![]() The associated calibrated power for the beacon at a distance of 1 meter is automatically calculated from the entered value and used for iBeacon/AltBeacon broadcasting.Įnter a URL to advertise in the Eddystone URL frame. Calibrated PowerĮnter a value between -1 and -127 for the calibrated power for the beacon at a distance of 0 meters. The lower 4-bytes of the instance ID are used to configure the major (high 2 bytes) and minor (low 2 bytes) for iBeacon/AltBeacon broadcasts. Instance IDĮnter an instance ID as a positive integer between 74976710655 inclusive. Instead, you generate the namespace ID either by entering a 128-byte UUID by pressing "Generate from UUID" or by entering a domain name by pressing "Generate from URI." In either case, the namespace ID and the iBeacon/AltBeacon UUID will be set using the generated value. The Eddystone namespace ID cannot be entered directly in the RadBeacon configuration app. If you leave the URL blank, then it will broadcast iBeacon/Altbeacon and Eddystone UID. If you configure a URL to be broadcast, then it will broadcast iBeacon/AltBeacon and Eddystone URL. The RadBeacon Dot Eddystone beacon can be configured to advertise iBeacon/AltBeacon and either Eddystone UID or Eddystone URL. The RadBeacon USB Eddystone beacon can be configured to advertise any combination of iBeacon, AltBeacon, Eddystone UID, and Eddystone URL (although you must choose at least one). Occasionally, a configurable beacon cannot be contacted by the app on the first attempt, so you may need to try again. If it is not configurable, an alert is displayed after 15 seconds indicating that the beacon could not be contacted for configuration. If it is configurable, then the configuration detail screen for the beacon is displayed. Tap on the beacon you would like to configure. Potentially configurable Eddystone RadBeacons should be identified in the list with the Bluetooth device name "RadBeacon G". This scans for beacons for 5 seconds and displays all beacons found during the scan. To start scanning for beacons, press the SCAN button in the upper right corner on the action bar. The main beacon scan screen is displayed which should be empty. In order to start scanning for beacons, first launch the RadBeacon configuration app. For details see "How do I put beacons into configurable mode?" Scan for Discoverable Beacons This can be done by power cycling the beacon. HCI sniffer - Bluetooth packet analyzer ver 5.First make sure you beacons are in configurable mode. Sorry I grabbed the wrong address.I'll do the ~ $ sudo hcitool lescanĬA:BC:21:70:5E:12 ~ sudo gatttool -b 0c:f3:ee:04:0d:e8 -I 'Host is down' implies to me that the Estimote is not advertising as connectable.'Page timeout' is likely the same thing. Status 0x04 handle 12 bdaddr FE:E7:60:FA:95:20 type ACL encrypt 0x00ĭouglas6 wrote:OK, that's an Estimote, not a RadBeacon. > HCI Event: Connect Complete (0x03) plen 11 > HCI Event: Command Status (0x0f) plen 4Ĭreate Connection (0x01|0x0005) status 0x00 ncmd 1 Write Class of Device (0x03|0x0024) ncmd 1Ĭode: Select all gatttool -t random -b aa:bb:cc:dd:ee:ff What does hcidump say when you try the connect command in ~ $ sudo hcitool lescanĬ5:AD:FF:72:28:09 ~ sudo gatttool -b fe:e7:60:fa:95:20 -IĬonnecting. ![]() Write Current IAC LAP (0x03|0x003a) ncmd 1 > HCI Event: Command Complete (0x0e) plen 5 > HCI Event: Command Complete (0x0e) plen 4 LE Set Scan Parameters (0x08|0x000b) ncmd 1 Sudo gatttool -b > HCI Event: Command Complete (0x0e) plen 4 HCI sniffer - Bluetooth packet analyzer ver 5.31ĭevice: hci0 snap_len: 1500 filter: 0xffffffff Opened up another terminal.not to sure what it all means You may need to add the '-t random' flag to the gatttool command. Douglas6 wrote:You should run hcidump in a separate terminal to get more information. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |